Short answer: no. Moissanite is silicon carbide, a crystal rather than a metal, so it cannot tarnish. Whatever went dark, yellow or green on your piece is the 925 sterling silver under the stones, or the plating over it.
Almost every message we get about tarnish is really a message about a piece that changed somewhere specific: the back of a chain that has gone dark while the front still looks new, a clasp that turned brassy, a green shadow on a finger after a hot day, a stone that looks flat in bathroom light. All four are real. None of them is the stone failing, and none of them is a piece that has been ruined. So the useful thing to do first is not to clean harder — it is to work out which part of the piece you are actually looking at, because the silver, the rhodium and the 18K gold plated finish each fail in their own way, at their own speed, and each has a different fix.
Tarnish, wear and dirt get talked about as one problem. They are three, and they leave different marks. Find your symptom in the table, then read the section it points to.
| What you see | What it actually is | What fixes it |
|---|---|---|
| Dark only where the piece touches you — the back of a neck, the palm side of a ring | Silver sulfide forming on bare 925 silver, where sweat and skin oils sit longest | A silver polish cloth, then dry storage. Nothing is damaged. |
| Dark only at the clasp, jump ring or link joints | The plating has thinned or gone at the points that rub against each other | Re-plate at a bench, or polish the silver underneath and wear it unplated |
| The whole piece has gone yellow or brassy | Gold plating worn through to the silver beneath — the layer is thinner than the eye expects | Re-plate. The metal is intact; only the finish is gone. |
| A green patch on skin, piece still looks fine | Copper in the 925 alloy reacting with sweat, soap or hand cream | Wash the skin, dry the piece. A plated finish reduces contact. |
| The stones look flat, grey or cloudy, but the metal is bright | A film of oil, cream, soap or sunscreen on the stone surface | Warm water, mild dish soap, soft brush. Never a repolish. |
Two of those five are chemistry on silver, two are wear on a finish, and one is neither — it is dirt. Only the fifth one is about the stone, and it is the only one that is entirely reversible in five minutes.
Tarnish gets described as a stain, which makes it sound like dirt. It is a chemical reaction. Jewelers Mutual, the jewelry trade's specialist insurer, puts it plainly: silver tarnish “is a chemical reaction between silver and sulfur,” and it “is a dark, often black, discoloration that forms on the surface of silver jewelry over time” — adding that while most people picture a dark patina, it “can also appear green.” Their list of what drives the reaction is worth reading, because it is almost entirely made of normal life: hydrogen sulfide in the air (concentrated in polluted cities), sweat and body oils, cleaning agents, hairspray and perfume, and the way the piece is stored.
The Gemological Institute of America makes the same point from the materials side in its care guidance: “Exposure to chemicals can damage or discolor precious metals – gold, silver and platinum.” (GIA, “Tips on Caring for Jewelry,” 10 December 2015.)
Now the stone. Moissanite is silicon carbide (SiC) — a compound, not an alloy, and with no free metal in it. In a peer-reviewed study in the journal Current Science, gemologist Kurt Nassau describes synthetic moissanite's stability directly: it holds in air to 1700°C (3092°F), in vacuum to 2000°C, and resists “most chemicals to well over 1000°C, except to fluorine, chlorine, molten alkalis and some molten metals.” (Kurt Nassau, “Synthetic moissanite: A new man-made jewel,” Current Science, Vol. 79 No. 11, 10 December 2000.)
One honest note on that sentence, because it contains the word “chlorine.” That list comes from a paper about industrial and high-temperature behavior, and it describes conditions an industrial furnace reaches, not conditions a swimming pool reaches. My reading — mine, not the paper's — is that a pool is not in that class. What a pool does threaten is the metal, which is a separate and much more ordinary problem: GIA notes that chlorine bleach “can pit or damage gold alloys.” We come back to that below.
“925” is not marketing language. Under the US Federal Trade Commission's jewelry rules, a piece may only be described as Sterling Silver if it is at least 925/1,000ths pure silver (16 CFR § 23.5(b)(2)). The other 75 parts per thousand are usually copper — and that copper is doing two jobs at once. It is what makes the alloy hard enough to wear every day, and it is the reactive part that sulfur and chlorine attack first. Jewelers Mutual notes the second consequence too: the copper in a sterling alloy can react with chemicals, “causing a green discoloration on the jewelry and your finger if you wear a sterling silver ring.”
So the sequence on a bare silver piece is predictable. Silver meets hydrogen sulfide in the air, or sulfur compounds in sweat and cosmetics, and silver sulfide forms on the surface — first a faint yellow-brown sheen, then the grey-black film everyone recognizes. It builds fastest where air and skin both reach: the back of a neck, the underside of a ring, the gaps between links. In a closed drawer in a humid summer it can arrive in weeks; on a chain worn twice a month and wiped down after each wearing, it takes far longer. Neither timing is a defect. It is the alloy doing what alloys do.
Where a piece is finished in rhodium, that silver is covered, and the alloy stays bright while the finish is intact. That is why the two words “rhodium plated” appear in our listings instead of something vaguer: 16 CFR § 23.7 states that it is unfair or deceptive to fail to disclose a rhodium surface layer on a product marked or described as precious metal. So we name the layer instead of leaving the metal undescribed. A piece with no rhodium and no gold over the silver is the simplest case of all: bare 925 silver with no barrier on it, which is why it warm-shifts first and why a polish cloth brings it back completely.
This is the table worth screenshotting, because it answers the question behind the question: if I buy this, what will I be looking at in a year? In our moissanite line these three constructions sit on the same 925 silver base; what changes is the layer on top.
| Construction | What changes | When it starts | Can it be saved | What keeping it costs |
|---|---|---|---|---|
| Bare 925 sterling silver, no plating | Silver sulfide film: dull grey first, then dark brown-black, heaviest on the skin-facing side | Weeks in a humid drawer; months on a worn chain; slower if stored dry and dark | Yes, completely. The film comes off with a polish cloth and no metal is lost beyond a trace | Nothing but a cloth. No service to buy, ever. |
| Rhodium plated over 925 silver | The rhodium itself holds its colour; what you notice is the layer thinning at contact points, then a dull silver patch showing through | Friction decides it: rings and bracelets first, earrings last. Trade guidance is six to eighteen months | Yes. A bench re-plate restores it; the piece underneath is undamaged | A re-plate, priced per piece by the jeweller doing it — we don't publish a number we can't stand behind |
| 18K gold plated over 925 silver | The colour holds while the layer is there; it wears at the clasp, link edges and the underside of a ring, and the silver beneath reads pale, not “black gold” | Same six to eighteen months, minus anything worn through the gym or the shower daily | Yes, by re-plating — or not at all: a worn plate is a look, not a fault | Same re-plate, quoted per piece. Cheaper than replacing the piece. |
Finish descriptions follow our own catalogue and the FTC jewelry rules cited above (16 CFR §§ 23.3, 23.4, 23.5, 23.7). General material behaviour follows GIA and Jewelers Mutual care guidance, both listed in the sources at the end of this page. Re-plating prices are set by the bench doing the work, not by us, which is why there is no figure in that column.
This is where most pages get vague, so here is what the US jewelry rules actually say, and which clause our own wording sits under. The thickness figure that gets quoted everywhere, 16 CFR § 23.4(b), is a rule about one specific word — vermeil. It reserves that word for sterling silver “coated or plated on all significant surfaces with gold, or gold alloy of not less than 10 karat fineness … and a minimum thickness throughout equivalent to two and one half (2 1/2) microns (or approximately 100/1,000,000ths of an inch) of fine gold” (16 CFR § 23.4(b), quoted directly). Read it the right way round: it is not a standard every gold-plated piece has to meet. It is the floor under the word vermeil.
We do not use the word vermeil on our pieces. Our plating has not been measured against that 2.5-micron line, so we do not borrow the word that sits on top of it — and we do not use “heavy gold electroplate” either, because that is the wording for the same 2.5-micron class. What our listings do say is “18K gold plated,” and that wording is governed by a different clause: 16 CFR § 23.3(b)(3) covers gold used to describe a surface layer rather than the whole article, and it requires that layer to be at least 10 karat fineness and at least 0.175 micron thick. So “18K gold plated” on a listing means 18-karat gold over 925 sterling silver at a decorative plating thickness — you can read those two words as meaning exactly what they say: a coating, not a solid gold surface.
On lifespan, the numbers in circulation come from the trade rather than from a laboratory, so treat them as guidance. Jewelers Mutual's rhodium-plating guide (22 May 2024) puts it the sensible way: plating “depends on how often you plan to wear the piece of jewelry and how well you take care of it,” and you will know it is time for a refresh “when the rhodium will wear away enough so you'll be able to see the base metal.” Where a figure is quoted, retailers generally put plating on frequently worn pieces at roughly six months to a year (Brilliant Earth) and up to around eighteen months on pieces worn less (the range quoted across plating guides such as Finematter and Millianna). Read those as expectations, not warranties: a ring worn through hand-washing and gym sessions will need attention far sooner than an earring worn twice a month.
This is a metal question with two different mechanisms, and it is worth separating them because only one of them can happen to our pieces.
The first is copper. As Jewelers Mutual describes it, the copper in a sterling alloy reacts with chemicals and produces green discoloration on the jewelry and on the skin. On a bare 925 silver ring, some people — more often in heat, or with hand cream in the picture — will see a faint green mark. It washes off the skin, it does not mark you permanently, and the jewelry itself is unharmed.
The second mechanism is the one behind most “my jewelry turned my neck green” stories, and Jewelers Mutual's rhodium guide names it: if a piece is made from brass and finished to look like a different metal, “you'll know it once the rhodium wears away, as your skin will turn green.” That is a base-metal story rather than a silver story. Our moissanite rings, chains, bracelets, earrings and pendants are built on 925 sterling silver rather than a plated base metal, and our stones are not metal at all — so the stone can never be the thing that leaves a mark on you. What we will not do is tell you it can never happen on any of our pieces: a rhodium finish reduces how much metal touches your skin, and that is a smaller risk than an unplated ring, not a guarantee.
If green marks specifically are your worry, the honest buying rule is short: choose a plated finish for pieces that sit tight against skin — a ring, a bracelet, a pendant resting on the collarbone — and expect to re-plate that piece eventually. On a chain hanging over a shirt, the contact is intermittent and the question matters less.
No — not from tarnish, and not from age. The “cloudy moissanite” claim is one of the more persistent pieces of folklore in this category, and the trade's own explanations of it agree on what is happening. Cullen Jewellery, whose bench services moissanite daily, writes that “moissanite does not naturally become cloudy or lose sparkle over time” and that “what is often perceived as cloudiness is usually surface build-up from everyday wear, such as hand cream, soap, oils, or dust” (Cullen Jewellery, moissanite care guidance, 17 December 2025). Keyzar reached the same conclusion and lists the culprits as oils, cosmetics and chemicals rather than the stone (Keyzar, “Does Moissanite Get Cloudy Over Time?”, 24 April 2022).
There is a good reason the crystal holds up. Nassau rates moissanite at 9¼ on the Mohs hardness scale, and notes that it lacks a pronounced cleavage plane — which is why it survives “all usual jewellery procedures such as setting, repairing and cleaning.” A material that can sit through a repair at a jeweller's bench without complaint is not going to be undone by your hand cream.
So a dull moissanite is a dirty moissanite, and the fix is the least glamorous advice in this article. GIA's method: “Most colored gems can be cleaned with warm water, mild dish soap (no detergents) and a soft brush.” Rinse it in a glass of water rather than under the tap, for a reason GIA spells out — “you risk losing loose stones – or even an entire piece of jewelry - if you rinse directly in the sink.” Five minutes, no repolishing, no re-cutting. The stone you bought is the stone you still have.
Two different questions travel with this one, and they have separate answers. What the stone is made of is covered in ما هو المويسانيت؟ الدليل الشامل 2026. Whether you can confirm what you were sent is its own subject — see Does Moissanite Pass a Tester? — and the short version is that a bench jeweler checks the stone itself, while a pocket heat pen cannot separate the two stones and was never built to.
Water does nothing to the stone, so the useful question is what the water is carrying. GIA's advice is direct: “Fine jewelry should be removed before diving into a chlorinated swimming pool or before using household cleaners,” and chlorine bleach specifically “can pit or damage gold alloys.” Jewelers Mutual is equally direct about silver: “Water is a major culprit in tarnishing. Remove your silver jewelry before showering, swimming or doing dishes,” adding that chlorine and ammonia accelerate tarnish.
Put together, that gives a practical ranking rather than a ban:
About ten minutes a month, and none of it needs a jewellery product we do not name here:
Care matters because these are two materials doing a lot of work across a wide price range. Below is the range per category, read from the NOVAE ATELIER catalogue, variant prices, 28 October 2026 — the start price, the top price, and how many catalogue listings sit in that range.
| Category | From | To | Listed pieces |
|---|---|---|---|
| Earrings | $29 | $339 | 95 |
| Rings | $29 | $585 | 77 |
| Bracelets | $63 | $903 | 20 |
| Necklaces & chains | $29 | $11,483 | 33 |
| Pendants | $29 | $1,959 | 48 |
| Watches | $149 | $1,599 | 35 |
| Grillz | $55 | $1,096 | 24 |
| Eyewear | $213 | $419 | 7 |
Source: read from the NOVAE ATELIER catalogue, variant prices, 28 October 2026, quoted in USD. Counts are catalogue listings by category, and two tennis bracelets are also listed under Chains, so those two appear in both rows. The top of the chain range is not a typo: $11,483 is the 18mm fully iced Cuban chain at 22 inches (NOV-CH-9455), the widest chain we make and the highest-priced piece in the catalogue. Most of our watches use a 904L stainless-steel case and band; five carry 925 silver, which is why that category behaves differently from everything else here.
By category, the care advice maps onto the price almost directly. The cheapest thing in the earrings range is also the easiest to keep clean; the most expensive chain is the one with the most square inches of finished surface to look after. Width, stone size and stone count are what move a chain's price within its range, and that arithmetic is broken out in the Cuban chain cost guide. Ring pricing by stone size and setting style is in the ring cost guide, and the bracelet range is covered in the tennis bracelet guide.
If the question you actually have is “will I notice, and will it annoy me”, the cheapest way to find out is to own both finishes and compare them on your own wrist. Three ways into the range, each at the starting price of its category:
Three sentences we are not going to write, and the reason for each, because a page about tarnish is only useful if it is honest about its own limits:
If you want the stone-level background, start with What Is Moissanite? and then the lab-grown comparison. For pendants specifically, sizing and chain pairing are in the pendant guide; for studs, the earring guide; for grillz, where metal sits in the mouth all day, the grillz guide covers the care rules that are specific to that piece. Bracelets as a category are on the bracelet collection page.
No. Moissanite is silicon carbide, a crystal rather than a metal, and tarnish is a reaction that happens on metal surfaces. There is nothing on the stone for sulfur to react with. What changes on a piece of moissanite jewelry is the 925 sterling silver under the stones, or the plating sitting on top of that silver.
Yes, eventually. Tarnish is a reaction between silver and sulfur, and it speeds up with humidity, air pollution, sweat, cosmetics and chlorine. The copper in a 925 alloy is the reactive part, which is also why a bare silver ring can leave a green mark on some people.
Trade and retailer guidance puts plating on everyday pieces at roughly six to eighteen months before re-plating, and less on rings, which take the most friction. How long it lasts depends on wear and care rather than a fixed clock, and it is the reason we describe our finishes as plated, never as permanent.
The stone cannot, because it is not a metal. A bare 925 sterling silver piece can leave a temporary green mark on some people, because of the copper in the alloy, and a plated piece built on a base metal such as brass will turn skin green once the plating has worn through. Our moissanite rings, chains, bracelets, earrings and pendants are built on 925 sterling silver, not a plated base metal, and a rhodium finish reduces how much metal touches the skin.
The stone, yes — water does nothing to silicon carbide. The finish and the silver are what you are protecting. GIA advises removing fine jewelry before a chlorinated swimming pool, and Jewelers Mutual advises removing silver jewelry before showering, swimming or doing dishes. Soap, chlorine and salt are where the shine actually goes.
Not permanently. What looks like cloudiness is a film of skin oil, hand cream, soap and sunscreen sitting on the surface, and it washes off with warm water, mild dish soap and a soft brush. The crystal underneath has no way to become hazy from the inside.
Read from the NOVAE ATELIER catalogue, variant prices, 28 October 2026: earrings from $29 to $339, rings $29 to $585, bracelets $63 to $903, chains $29 to $11,483, pendants $29 to $1,959, watches $149 to $1,599, grillz $55 to $1,096 and eyewear $213 to $419. The top of the chain range is an 18mm fully iced Cuban chain, 22 inches.
Tell us how you wear your jewelry — every day, weekends, gym, showers — and we will tell you which finish we would put on the piece ourselves, and what it costs. If you already own a piece from us and the finish has dulled, send a photo and we will tell you whether it needs a clean or a re-plate.
اسأل على واتسابSources: US Federal Trade Commission jewelry guides, 16 CFR § 23.4(b) (the reserved term for vermeil: sterling silver, at least 10 karat gold, at least 2.5 microns, quoted directly), § 23.3(b)(3) (gold-plated articles: at least 10 karat fineness, layer at least 0.175 micron thick), § 23.5(b)(2) (silver content) and § 23.7 (disclosure of a rhodium surface layer, quoted directly); Gemological Institute of America, “Tips on Caring for Jewelry,” 10 December 2015 (cleaning method, chlorinated pools, chlorine bleach and gold alloys, ultrasonic cautions, anti-tarnish storage, six-month check); Jewelers Mutual, “Does sterling silver tarnish?” (17 September 2024), “What is Rhodium Plating? All You Need to Know!” (22 May 2024) and “How to Store Jewelry” (22 July 2026) (tarnish chemistry, sulfur sources, water and chlorine, green discoloration, plating wear, polishing advice, airtight storage and anti-tarnish strips); Kurt Nassau, “Synthetic moissanite: A new man-made jewel,” Current Science Vol. 79 No. 11, 10 December 2000 (hardness, cleavage, chemical and thermal stability); Cullen Jewellery, moissanite care guidance, 17 December 2025 (cloudiness, quoted directly); Keyzar, “Does Moissanite Get Cloudy Over Time?”, 24 April 2022. Plating-lifespan figures are retailer and trade guidance, not laboratory measurements, and are attributed as such above. Prices are read from the NOVAE ATELIER catalogue, variant prices, 28 October 2026, in USD. This page describes how the materials in our jewelry behave; it is not a warranty, and normal wear is normal.
Made to order in our Guangzhou atelier — 925 sterling silver where listed, hand-set moissanite.
Everything here is made and set on our own bench in Guangzhou — 925 sterling silver and moissanite, with gold-tone plated alloy watch cases where the listing says so. If you are buying for a store, a brand or a reseller, the wholesale pages carry the minimums, lead times and terms:
Retail pieces in the same workshop: 16mm Cuban link chain · 18mm iced Cuban chain · RAM iced out pendant · Iced out square-case watch